Zynsonix Link

September 26, 2011

Modifying the Fostex T50RP Headphones

There are many instances in headphone-dom when a headphone has potential that may not have been fully realized by the manufacturer. It's then that the trusty headphone modder wields his magical dremel and goes to work for the good of the audiophile community.

Just that has happened with the Fostex T50RP headphones. Fostex is a Japanese company really known for their specialty drivers (especially full range) and they have some clout in the pro audio industry as well. The T50RP are the flagship model of the Fostex RP lineup (consisting of the T20RP, T30RP and T50RP). Flagship may sound expensive if you're familiar with headphone manufacturers like Sennheiser, Grado or Sony, but these are only $80 or so. An $80 headphone from a company not really known for their headphones may seem kinda humdrum, but the driver housed in the headphone is fairly unique. From the Fostex site: "The newly developed RP Diaphragm improves the overall frequency response ... employing copper foil etched on a polyimide film Neodymium magnet for high sensitivity and excellent transient handling." Bottom line for those who just glazed over, this is an orthodynamic headphone and a smidge cheaper it's ortho-cousins: the HiFiMan HE-5LE ($699) or the Audeze LCD-2 ($945).



The Fostex T50RP

HeadFier Smeggy took it upon himself to extract the best the Fostex T50RP could deliver, removing them from the shackles of under-damped plastic cups and vinyl pads, creating something that would be forever known as the Thunderpants. Smeggy (aka Gary) removes the driver from the headphones and installs it in a well-sealed ported wood enclosure, replaces the pads and cable, installs a leather headband and does a few other tweaks.  

So how does a modified T50RP sound? I have no idea; I'm going to try and build one to find out. My first modus operandi was to locate a set of pretty wood cups that would house the drivers. I turned to a wood turner on HeadFi and commissioned him to build me the cups and baffles as I don't have a lathe to handle such delicate work (for the sake of privacy I won't be providing his contact information at this time).


T50RP wood cups and baffles

T50RP wood cups and baffles, reversed

The first easy bit of work would be to trim a pair of felt circles to drop in the wood cups to prevent sound reverberations and hammer in a pair of brass fittings into the bottom port on the cups. 




I went ahead and did some depth mounting for the screws on the baffles so the pads would sit flat across them. 


Baffles with depth mounted screw holes

They were then sealed, stained and poly-coated, even though they wouldn't be seen once the pads were in place. If anything, it would help preserve the wood and prevent the rough finish from wearing against the pads. 

Stained and sealed baffles

The drivers from the stock T50RP need to be removed, which is about as simple as unscrewing a few screws after removing the pads and snipping the two wires running to the unit. At the recommendation of Sachu, who has also heavily modified his T50RPs, porous tape was applied to the four corner quadrants on the back of the driver. The three plastic screw-holders around the frame were then drilled out and tapped for #4 screws so they could be screwed directly to the new wood baffles.

Porous tape in corner quadrants on driver

There's a bit of a gap between the drivers and the baffles that will need to be sealed, to minimize this gap, a piece of Dynamat Xtreme was trimmed and smoothed to fit around the driver opening.


Dynamat added to driver bracket

Now the baffles will be prepped to accept the drivers. Small holes were drilled to accept the #4 screws and an outline drawn to see where the caulking would need to be. 


Prepped Baffle

I elected to add a bit of speaker grill fabric from PartsExpress to separate the driver from the ear, adding a modicum of comfort and perhaps softening the higher frequencies. The driver surrounds were loaded with speaker caulking (also available at PartsExpress), which is a rubber sealant that performs a bit like blu-tack. This will seal the driver to the baffle. 

Grill fabric attached by adhesive

Grill fabric on the baffle

The drivers are then carefully lined up with the pre-drilled holes on the baffle and screwed in place. The speaker caulk is smoothed around the edge to ensure it's air-tight. 

Drivers caulked to the baffles

Next comes the point where the driver cups are fastened to the headband. Since the original hardware can't be used with the wood cups, new hardware has to be fashioned. I offered Smeggy to purchase a set of his hardware as he does such a nice job with it, but he seems to be tied down with popularity at the moment. So that leaves it up to me. 

The first requirement is a piece that will attach the wood block to the wood cups. Shelf brackets were procured from Home Depot, which were then dremelled, drilled and the holes depth mounted. 

Shelf brackets re-purposed for the T50RPs
Next came the creation of the wood blocks that would act as a pivoting joint between the cups and the headband. The blocks were cut from a spare piece of Red Oak from Home Depot using a jigsaw, then sanded down by hand and the small concave area on the bottom was created using a Dremel sanding wheel at a nice slow setting. The holes were trimmed out on the drill press. Once satisfied with the shape, two coats of oil-based stain were brushed on, then two coats of satin polyurethane. The small hole on the bottom was then threaded for a size six screw.

Wood blocks to fasten the cups to the headband

Finally, the headphone could begin to be put together. Loctite Adhesive was used to ensure the copper colored pipes wouldn't ever slip out of the wood blocks. The gold shelf brackets were screwed to the blocks firmly, but not overly so, as the cups would need the ability to be pivoted back and forth at slight angles.

Wood block swivel room

Now the cable could be soldered to the driver. I prepared a nice high-quality Zynsonix Vray Prime cable made with Cardas copper for the T50RPs. The wire was sleeved with soft black nylon multifilament and terminated with a Furutech FP-704G 1/4" TRS connector and the "Y" split covered with a sleek ViaBlue cover. This was run through the cups and soldered to the terminals. Speaker caulking was then placed where the baffle and cups would come together for sealing purposes, along with the area where the cable enters the cups. Wires are held with a zip-ties as a strain relief system; simple but effective.      

Speaker caulking around the circumference to seal cups

The baffles were then screwed in place with four wood screws each. Care must be taken when screwing into wood as it can strip easily. 


Baffles screwed in place

All that's left is to fit the super expensive Stax Omega II pads and we have a finished headphone!

Brown Stax Omega II pads in place

Finished T50RPs
So, now that they are complete, it begs the question; "how do they sound?" I was actually quite surprised with the quality, given that this headphone started its life as an $80 set of cans. It can easily hold its own against some of the nicer dynamic cans like the Denon D7000. The bass is tight and articulate, the treble very informative but not harsh, and the whole dynamic range has a nice overall clarity that is almost reminiscent of an electrostatic headphone. I would agree with all that I've heard regarding the seal of the headphones. The cups need to be cupping your ears evenly for the best sound. I wish I was able to compare it to the HiFiMan or Audeze headphones, but I haven't been able to audition either as of yet. All in due time.

If you're looking to have your Fostex T-50RPs recabled or damped, or any other headphone, give Zynsonix Audio a shout.

 
The Fine Print:
The above steps detailing the recabling of a headphone are for entertainment purposes only, and not to be performed under any circumstances. The owner of this blog and all associated parties can not / will not be held responsible if you attempt the process posted and cause physical harm to yourself, your surroundings or your property. Please keep this in mind.
 











9 comments:

  1. Fellow Head-Fier here...Looking great. Can't wait to see the finished product.

    ReplyDelete
  2. Very impressive. I hope they sound as good as they look.

    ReplyDelete
  3. What amp are you using to drive these?

    ReplyDelete
  4. I'm using a Bottlehead S.E.X. with very good results.

    ReplyDelete
  5. Thanks for this, the photos are very clear as is the information!

    I love the sound of my Fostex but if this makes them even better than I am all for that!, they are UGLY in their standard form but yours are much nicer, my father has always messed around with wood, making useless wooden bowls on a lathe LOL, so I will get him to turn me some wooden ear cups & I will get cracking on this mod, I am thinking cherry or cocobola at the moment.

    I use my Fostex TR50P's with a NJC monitor II headamp as I have found that this amp really has a lot of juice (power) & can really make these headphones sing & dance like I have never heard before on other amps ive tried so I think people are correct when they say these love powerful amps, I just cant wait to hear them when fully modded.

    Thanks again bud!

    ReplyDelete
  6. Glad to hear you're getting started on your own set, good luck with the build! :)

    ReplyDelete
  7. Amazing this speaker,i hope this sound is clear and impressive.Thanks for sharing.:)

    ReplyDelete
  8. Where can I find Cups ?

    ReplyDelete
  9. what is the dimensions for your baffles and cups?

    ReplyDelete