Pono Player Balanced Interconnect Cable

So you've taken the plunge on Neil Young's sweet little Pono player, however it uses a unique way to export those tunes to your balanced headphones or balanced rig. I'll be covering how I built an unbalanced cable, and how to build a balanced pair of cables so you can extract every juicy detail from those Hi Res tracks. As you may know, Zynsonix Audio offers these in any length or configuration, so reach out if you need one.

The Pono player features dual stereo 3.5mm outputs. You can use these to output to a pair of balanced headphones, a balanced rig that uses 3 pin XLRs (or mini XLRs / TRS plugs), or a single ended rig that takes good-old-fashioned RCAs.

Neil Young's Pono Player

Stereo 3.5mm connectors have three connections, the sleeve, the ring and the tip. When used in typical applications, the sleeve is a shared ground, the ring is the right signal, and the tip is the left signal. However not the case with the Pono in balanced mode.

Tip, Ring and Sleeve on a 3.5mm mini connector

In the case of the Pono player in balanced mode, each of the two 3.5mm goes to an individual three pin XLR. The Sleeve, as you'll note below, connects to the Pin 1 (ground). The Ring connects to Pin 3 (negative). The Tip connects to Pin 2 (positive). For a balanced headphone cable, you will note that the Sleeve connection is not used, only the tip (positive) and the ring (negative). These schematics are straight from the engineers over at Ayre Acoustics. If I'm not mistaken, this is going to be the portable standard for balanced connections including on upcoming models from Sony.

Pono Player wiring pinout / diagram

I made a handy dandy visual for the back of an XLR connector (note mini XLRs are different!) so you can see the pin assignments.

XLR pinout for reference

Below you'll see the pair of 3.5mm stereo mini to XLR cables using the great sounding Zynsonix Trebuchet 99.99997% pure ohno cast copper. The Viablue XLRs are very sleek looking, well made and use set screws rather than a traditional boot or crimp sleeve. The Amphenol mini connectors are my new favorite value connector, they offer a great connection and a recessed area near the barrel that allow them to be used with phone cases and portable DAPs with cramped faceplates.   

Pono balanced interconnect cable

All done and we have a pretty pair of Trebuchet interconnects for your Pono player. Off they go to a happy customer.

I hope you enjoyed this post on building a pair of interconnects for a Pono Player. Please reach out to Zynsonix Audio if you'd like your own custom Pono interconnects (balanced or single ended) or headphone cable, and keep enjoying those high res tracks!

The Fine Print:

The above steps detailing the build of a Pono player cable are for entertainment purposes only, and not intended to be used as assembly instructions. The owner of this blog and all associated parties can not / will not be held responsible if you attempt the process posted and cause physical harm to yourself, your surroundings or your property. 

Pure Silver Mini to Mini Cable

A short mini to mini cable cable can be very handy when connecting a portable audio player to a portable amplifier. In some cases it's worthwhile to use a digital audio output, but not all portable devices offer this, so the venerable 3.5mm mini to mini will work perfectly well. In this particular post, I will be assembling a mini to mini cable using Cardas 5N (99.999% pure) silver wire and a pair of Neutrik mini connectors, the Neutrik NYS-231 BG to be exact. The B in the nomenclature stands for the black shell, and the G stands for gold contacts. This particular connector is chosen over the Switchcraft 35HD and the Canare F12 as the body is smaller and more easily fits on the face plate of portable amplifiers. You'll notice below that the connectors come in three parts, the connector piece with solder tabs, a barrel and a small tube that acts as a dielectric so the left and right solder joints do not short to the barrel, which is connected to ground.

A pair of Neutrik NYS-231BG

You may notice that the barrel inlets are rather small and not completely ideal for thicker sleeved cable. Because of this, I dremeled out the barrel inlet to create a larger opening. 

Barrels dremeled for larger diameter cable

Once this is complete, it is necessary to sand or file the rough areas so they don't grind up against the wire during use. Once the barrels are prepared, the solder tabs should be identified with a multimeter. In this case, the shorter leg A is the left signal (aka tip), the longer leg B is the right signal (aka ring), and C is ground (aka sleeve). 

Pinout of the Neutrik mini connector

As mentioned above, this cable will be using solid silver wire from Cardas. This wire will be sleeved with Teflon (PTFE) tubing. 

Cardas silver wire and Teflon tubing

Each wire is trimmed to the appropriate length and the Teflon tubing is then slipped over top. The Teflon acts as a dielectric and prevents the strands (aka conductors) from shorting to one another. It's a very good idea to get Teflon that's for a larger gauge than the wire you are using so it slips over it easily. In this case, 24 gauge silver is covered with 22 gauge Teflon.

Silver wire sleeved with Teflon

The three wires are braided together and soldered to the Neutrik connector. It's important for the Teflon tubing to go right up to the solder taps to prevent shorting.

Silver wire soldered to the Neutrik connector

Next comes the black nylon multifilament sleeving made by Techflex. This is 3/16" size, cut to length using a hot knife from Partsexpress. The hot knife prevents fraying at the ends by slightly melting where it cuts. Also note the dielectric material is slid in place before the barrel is screwed on. 

Black Nylon Multifilament

The barrel can then be screwed in place, and the other Neutrik connector installed the exact same way. In the photos below, 1/2" heat shrink is slipped over the barrels to provide additional strain relief and to offer the feel of a "rubberized"-type layer.  

Completed mini to mini cable

This can now be the connection between a portable audio player and a portable amp and not take up much real estate at all. Thanks for taking them time to read this post. If you are interested in purchasing a completed mini to mini cable, please contact Zynsonix.com.

For more pure silver goodness, check out a previous post detailing the build of pure silver interconnects. 

The Fine Print:
The above steps detailing the building of a cable are for entertainment purposes only and not to be performed under any circumstances. The owner of this blog and all associated parties can not / will not be held responsible if you attempt the process posted and cause physical harm to yourself, your surroundings or your property. Please keep this in mind.