So, as you have probably noticed, headphone manufacturers are not very good about standardizing connectors for use with headphones and amplifiers, to the point of absurdity. I am going to try and document most of the different headphone connector pin diagrams aka pinouts in one place so you don't have to pull out your hair tracking them down. If you need a cable built with any of the connectors below, reach out to Zynsonix Audio.
The 2.5mm TS with narrow shoulders originally was created for use with the Sennheiser HD700 headphone cups, but now has also been adopted for the Oppo PM-1, Oppo PM-2 and can potentially be used with the HiFiMan 400S, HE-560, HE-1000 and Edition X as the stock TRS does not use the ring (R). The tip is used for signal/positive, and the sleeve is ground/negative.
Recommendations: The best I've found are unbranded/generic connectors with the gold plated connector, chrome barrel and "long shoulders" which looks like the illustration above. I don't advise the other plastic/nickel plated plugs.
Recommendations: As of right now, the best 2.5mm TRRS is made by Furutech, the FT-7254(R), but you'll pay for it at $35 a pop. Otherwise, Aliexpress is a good source if you purchase from a reputable vendor, and you can get fancy with carbon-fiber barrels, etc.
Hifiman HM-901: Tip is L+, the ring closest to the tip is R+, the ring closest to the sleeve is L- and the sleeve is R-
Geek Out V2: Tip is L+, the ring closest to the tip is R+, the ring closest to the sleeve is L- and the sleeve is R-
Custom Red Wine Audio can feature this jack: RWAK240, RWAK380 and MZAK240
JH JH3A digital connection - Tip is left (L), ring closest to tip is right (R), the second ring handles digital coaxial information, and the sleeve is ground for both analog and digital.
Leave it to Sony to come up with some weird format that confuses the market further ;) #Beta. To be honest I actually kinda like this connector. It's easier to work with than the teensy-tiny 2.5mm TRRS and less likely to break off in a jack due to the added girth. I still think the ideal connector should be locking with pins like a mini XLR versus spring tension like with this TRRRS, but since this is likely only going to be used with higher-end DAPs, the females have been of high quality so far and don't seem predisposed to failing over time.
I haven't seen the ground sleeve being used for anything yet, but from the tip, the connections are left signal positive (L+), left signal negative (L-), right signal positive (R+) and right signal negative (R-).
The 1/4" TRS (aka 6.25mm TRS for the metric folks) is the most ubiquitous plug for home/studio headphones. The tip is left signal (L), the ring is right signal (R), and the sleeve is ground (G).
The Male SMC connector is used to connect to older HiFiMan headphone cups, and current models such as the HE-6. As you can see from the pinout, the signal is the small center pin, and the ground is the textured area at the end of the connector. Care should be used when soldering the ground, as using too much solder will prevent the brass cover from sliding over.
The Sennheiser HD connector features two pins. It's difficult to notice on a quick glance, but one is larger than the other. The larger pin should be used for ground/negative, and the smaller pin is signal/positive.
Recommendations: There are only a couple of DIY connectors out there that are compatible with the Sennheiser HD265, HD525, HD535, HD545, HD565, HD565 II, HD580, HD600 and the HD650. ... Cardas and Furutech, the Cardas HPSC and Furutech FT-2PS.
The Cardas HPSC is reasonably priced ($~16 as of this writing), but not ideal for beginners. It's a flexible molded plastic with not much room for the wire to be soldered to the internal pins, and the rhodium needs to be heated enough so the solder takes, but not enough for the plug to melt. Flux can be helpful for this, and I personally fill the cavity with a plastic-like hardening adhesive for longevity. The Furutech FT-2PS runs quite a bit more (~$46 as of this writing, but makes the soldering much easier by separating the pins with plastic, features an internal clamp for strain relief, is made of tough plastic, and looks great. So personally, I would purchase the Furutech unless cost is an issue.
The Fine Print: This page is for entertainment purposes only and is not intended to substitute or supercede what a manufacturer states or recommends for their product. Zynsonix Audio, LLC does not furnish any guarantee for the accuracy of information herein, and does not assume responsibility for damages sustained by entities referencing this information for any reason.
Zynsonix guarantees all cable and headphone work performed by Zynsonix Audio, LLC to be correct, however does not guarantee the work of other entities, whether individuals or businesses, that make use of this information.
The 2.5mm TS with narrow shoulders originally was created for use with the Sennheiser HD700 headphone cups, but now has also been adopted for the Oppo PM-1, Oppo PM-2 and can potentially be used with the HiFiMan 400S, HE-560, HE-1000 and Edition X as the stock TRS does not use the ring (R). The tip is used for signal/positive, and the sleeve is ground/negative.
Recommendations: The best I've found are unbranded/generic connectors with the gold plated connector, chrome barrel and "long shoulders" which looks like the illustration above. I don't advise the other plastic/nickel plated plugs.
______________________________________________________________
The 2.5mm TRS is found on some mobile phones, although most use the ubiquitous 3.5mm TRS. The tip is left signal (L), the ring is right signal (R), and the sleeve is ground (G).
HiFiMan headphones (New Models): includes the updated HE400S and HE560, HE1000 and Edition X, which use this connector at the cups. Per measurements, the tip is the positive, the sleeve is the negative, and the ring doesn't appear to be used.
HiFiMan headphones (New Models): includes the updated HE400S and HE560, HE1000 and Edition X, which use this connector at the cups. Per measurements, the tip is the positive, the sleeve is the negative, and the ring doesn't appear to be used.
Recommendations: As of right now, the best 2.5mm TRRS is made by Furutech, the FT-7254(R), but you'll pay for it at $35 a pop. Otherwise, Aliexpress is a good source if you purchase from a reputable vendor, and you can get fancy with carbon-fiber barrels, etc.
_____________________________________________________________
The 2.5mm TRRS is commonly used for balanced operation for Astell and Kern portable digital audio players. Tip is right negative (R-), ring closest to tip is right positive (R+), ring closest to sleeve is left positive (L+) and sleeve is left negative (L-).
Other applications:
Onkyo portable DP X1 DAC: Tip is right negative (R-), ring closest to tip is right positive (R+), ring closest to sleeve is left positive (L+) and sleeve is left negative (L-). : Source
Recommendations:
Other applications:
Onkyo portable DP X1 DAC: Tip is right negative (R-), ring closest to tip is right positive (R+), ring closest to sleeve is left positive (L+) and sleeve is left negative (L-). : Source
Recommendations:
_____________________________________________________________
The HiFiMan HM-801 digital media player and Oppo PM-3 headphone (balanced) follow this unique configuration using the 2.5mm TRRS. Tip is left positive (+), ring closest to tip is right positive (+), ring closest to sleeve is left negative (L-) and sleeve is right negative (R-). Get yourself a nice aftermarket cable using the TRRS from Zynsonix Audio.
_____________________________________________________________
The 3.5mm connector (aka mini connector) is the most ubiquitous plug used for portable audio. The tip is left signal (L), the ring is right signal (R), and the sleeve is ground (G).
HiFiMan is now using 3.5mm plugs for some of their headphones as well like the HE-560 v3 just to keep us all on our toes. I have not tested a stock cable for the 560 v3, but using the tip for positive and connecting the ring and ground to negative works perfectly well. They're probably not using the ring like previous designs.
HiFiMan is now using 3.5mm plugs for some of their headphones as well like the HE-560 v3 just to keep us all on our toes. I have not tested a stock cable for the 560 v3, but using the tip for positive and connecting the ring and ground to negative works perfectly well. They're probably not using the ring like previous designs.
Recommendations: There are tons of great options out there from Switchcraft, Canare, Oyaide, ViaBlue, Amphenol and more:
Amphenol K Series: Great value and there is an extended shaft version for use with phone cases.
Canare F12: Perfect if you are using thick cable thanks to the large barrel, but a bit heavy and may not fit some devices due to size.
Furutech FT-735 (R): I personally avoid this rhodium plated 3.5mm, the ground sleeve does not accept solder even at high temperatures in my experience and I had one where the tip broke off.
Neutrik REAN NYS231: Very slightly smaller than the Switchcraft, not as well made in my humble opinion, but low cost and works. If you have the scratch step up to the Amphenol K Series.
Oyaide: A bit overpriced in my opinion, but the long shaft version is one of the only connectors I know of that can fit Ultrasone headphones.
Switchcraft 35 HD series: A rugged, U.S. made plug, medium-sized and easy to use. The right angle version is very solid. If you order a ton of the right angle versions, be sure to test them before use... in rare cases you can run into a dud (in my experience).
ViaBlue T6s: If you're looking for audio jewelry, this will scratch your itch. The strain-relief system is a little awkward with set-screws and different-sized plastic rings, otherwise relatively easy to use. There are two sizes, small and regular.
Amphenol K Series: Great value and there is an extended shaft version for use with phone cases.
Canare F12: Perfect if you are using thick cable thanks to the large barrel, but a bit heavy and may not fit some devices due to size.
Furutech FT-735 (R): I personally avoid this rhodium plated 3.5mm, the ground sleeve does not accept solder even at high temperatures in my experience and I had one where the tip broke off.
Neutrik REAN NYS231: Very slightly smaller than the Switchcraft, not as well made in my humble opinion, but low cost and works. If you have the scratch step up to the Amphenol K Series.
Oyaide: A bit overpriced in my opinion, but the long shaft version is one of the only connectors I know of that can fit Ultrasone headphones.
Switchcraft 35 HD series: A rugged, U.S. made plug, medium-sized and easy to use. The right angle version is very solid. If you order a ton of the right angle versions, be sure to test them before use... in rare cases you can run into a dud (in my experience).
ViaBlue T6s: If you're looking for audio jewelry, this will scratch your itch. The strain-relief system is a little awkward with set-screws and different-sized plastic rings, otherwise relatively easy to use. There are two sizes, small and regular.
The 3.5mm TRRS has quite a few applications:
iPhone and many other mobile phones: The tip is left signal (L), the ring closest to the tip is right signal (R), the ring closest to the sleeve is ground (G), and the sleeve is the microphone connection.
Oppo PM-3 headphones: This is used for the balanced cup connection for the Oppo PM-3. Per Oppo, the tip is L+, the ring closest to the tip is R+, the ring closest to the sleeve is L- and the sleeve is R-
iPhone and many other mobile phones: The tip is left signal (L), the ring closest to the tip is right signal (R), the ring closest to the sleeve is ground (G), and the sleeve is the microphone connection.
Oppo PM-3 headphones: This is used for the balanced cup connection for the Oppo PM-3. Per Oppo, the tip is L+, the ring closest to the tip is R+, the ring closest to the sleeve is L- and the sleeve is R-
Hifiman HM-901: Tip is L+, the ring closest to the tip is R+, the ring closest to the sleeve is L- and the sleeve is R-
Geek Out V2: Tip is L+, the ring closest to the tip is R+, the ring closest to the sleeve is L- and the sleeve is R-
Custom Red Wine Audio can feature this jack: RWAK240, RWAK380 and MZAK240
JH JH3A digital connection - Tip is left (L), ring closest to tip is right (R), the second ring handles digital coaxial information, and the sleeve is ground for both analog and digital.
For DIY Audio Parts, check out
_____________________________________________________________
Leave it to Sony to come up with some weird format that confuses the market further ;) #Beta. To be honest I actually kinda like this connector. It's easier to work with than the teensy-tiny 2.5mm TRRS and less likely to break off in a jack due to the added girth. I still think the ideal connector should be locking with pins like a mini XLR versus spring tension like with this TRRRS, but since this is likely only going to be used with higher-end DAPs, the females have been of high quality so far and don't seem predisposed to failing over time.
I haven't seen the ground sleeve being used for anything yet, but from the tip, the connections are left signal positive (L+), left signal negative (L-), right signal positive (R+) and right signal negative (R-).
_____________________________________________________________
The 1/4" TRS (aka 6.25mm TRS for the metric folks) is the most ubiquitous plug for home/studio headphones. The tip is left signal (L), the ring is right signal (R), and the sleeve is ground (G).
Recommendations: I find the Neutrik NP3C-BAG to be a great value 1/4" connector and the Furutech FP-704 (G) to be a great choice if you want to spend a few more dollars.
______________________________________________________________
The mini XLR has become quite popular in the headphone market as it is relatively small, it locks in place, and the connections are more reliable than your average TRS. The mini XLR 3 pin is commonly used by AKG for their K-240S, K271 MKII, K701, K702. K712 and other K701 derivatives like the Quincy Jones Q701. The pins are labeled on nearly all mini XLR connectors, though you may have to look under a light to see them.
For the standard AKG wiring, pin 1 is ground, pin 2 is right signal and pin 3 is left signal.
Recommendations: The tried and true is the Switchcraft TA-3, however I prefer the REAN RT3FC and RTCMC models at the same price as they seem a little more sturdy and have two different strain relief sizes depending on your wire size. The Furutech FT-610 resembles the Switchcraft, however has nicer rhodium plated connectors and looks a little prettier. Bottom line, if you want the best available, go with the Furutech, and if you need the best value, go with the REAN.
_____________________________________________________________
The standard-sized XLR is used for a few different applications. As an audio interconnect, Pin 1 is the ground, Pin 2 is the positive signal, and Pin 3 is the negative signal. You'll notice that most XLRs have the pins labeled 1, 2 and 3 if you look closely enough.
Recommendations: The Neutrik XX series is a great value. I also like the solid weight and feel of the Switchcraft AAA series, and they're two piece, so a little easier to assemble. If you'd like super solid and have a couple more bucks to spare, the Furutech FP series is a nice choice.
_______________________________________________________________
Headroom initially debuted their first balanced headphone amplifier in a dual 3 pin configuration (I suppose if someone wanted to have headphone monoblocks in the future), however the 4 pin XLR proved to make more sense as it's an easier, less cumbersome implementation. You'll notice that most XLRs have the pins labeled if you look closely enough. Pin 1 is L+ (left positive), Pin 2 is L- (left negative), Pin 3 is R+ (right positive), Pin 4 is R- (right negative). Nearly all balanced headphone amps use this configuration, as well as the legendary AKG K1000.
Recommendations: The same recommendations from the 3 pin XLRs are echoed here: Neutrik XX series is a great value. I also like the solid weight and feel of the Switchcraft AAA series, and they're two piece, so a little easier to assemble. Furutech also just released (FINALLY!) a 4 pin XLR, the FP-705 in 2016, which is a great choice for a few more dollars.
For DIY Audio Parts, check out
_____________________________________________________________
As mentioned above, Headroom initially debuted their first balanced headphone amplifier in a dual 3 pin configuration. It still sticks around today, however is not as popular as the 4 pin configuration. You'll notice that most XLRs have the pins labeled if you look closely enough. Pin 1 (typically the ground) is not used for balanced headphones. Pin 2 is used for the positive signal, and pin 3 is the negative signal. In this diagram, the white wire is left positive (+), the orange wire is left negative (-), the red wire is right positive (+), and the blue wire is right negative (-).
Recommendations: The same recommendations from the 3 pin XLRs are echoed here: Neutrik XX series is a great value. I also like the solid weight and feel of the Switchcraft AAA series, and they're two piece, so a little easier to assemble. If you'd like super solid and have a couple more bucks to spare, the Furutech FP series is a nice choice. Also the Cardas CG series is pure eye candy and a popular choice of my clients.
_____________________________________________________________
The Kobiconn Auto IRIS is an odd little connector typically used with cameras. These are found on Ray Samuels (RSA) balanced portable headphone amplifiers like the Protector and SR-71B, however are also on amplifiers Centrance GloveAudio A1, HiFi M8, and the ALO Rx Mk3 B. Pin 1 is left positive (L+), pin 2 is right positive (R+), pin 3 is left negative (L-), and pin 4 is right negative (R-).
_____________________________________________________________
The Male SMC connector is used to connect to older HiFiMan headphone cups, and current models such as the HE-6. As you can see from the pinout, the signal is the small center pin, and the ground is the textured area at the end of the connector. Care should be used when soldering the ground, as using too much solder will prevent the brass cover from sliding over.
______________________________________________________________
Recommendations: There are only a couple of DIY connectors out there that are compatible with the Sennheiser HD265, HD525, HD535, HD545, HD565, HD565 II, HD580, HD600 and the HD650. ... Cardas and Furutech, the Cardas HPSC and Furutech FT-2PS.
The Cardas HPSC is reasonably priced ($~16 as of this writing), but not ideal for beginners. It's a flexible molded plastic with not much room for the wire to be soldered to the internal pins, and the rhodium needs to be heated enough so the solder takes, but not enough for the plug to melt. Flux can be helpful for this, and I personally fill the cavity with a plastic-like hardening adhesive for longevity. The Furutech FT-2PS runs quite a bit more (~$46 as of this writing, but makes the soldering much easier by separating the pins with plastic, features an internal clamp for strain relief, is made of tough plastic, and looks great. So personally, I would purchase the Furutech unless cost is an issue.
This is a work in progress and there are still a few connectors to add ;)
The Fine Print: This page is for entertainment purposes only and is not intended to substitute or supercede what a manufacturer states or recommends for their product. Zynsonix Audio, LLC does not furnish any guarantee for the accuracy of information herein, and does not assume responsibility for damages sustained by entities referencing this information for any reason.
Zynsonix guarantees all cable and headphone work performed by Zynsonix Audio, LLC to be correct, however does not guarantee the work of other entities, whether individuals or businesses, that make use of this information.
